User Guide To Connecting Biometric Device To Paycheckmaster Standard (Anviz W1 Pro & ZKTeco WL 20)
To read the full guide complete with pictures, click here: User Guide To Connecting Biometric Device To Paycheckmaster Standard (Anviz W1 Pro & ZKTeco WL 20)
Anviz W1 Pro
- Turn on the Anviz W1 Pro.
- Log in as an administrator using user ID “0” and password “12345”. NOTE: “0” and “12345” are the default administrator credentials when the device is first acquired. Contact any higher-ups if the credentials required may have been changed since first use.
- At the Main screen, go to Network.
- At the Network screen, go to Internet.
- Change WAN mode to Ethernet.
- Go back to the Network screen, then go to Ethernet.
- Set Option to “Active”.
- Set Retrieve IP mode to “DHCP”.
- Set Get DNS to “Auto”.
- Go back to the Network screen, then go to Comm Mode.
- Set Comm mode to “client”.
- Set Port to “5010”.
- Set Comm.PW to “Enabled”.
- Set PW Setting to “12345”.
- Set Server Type to “IP Address”.
- Set server IP to the IP address of the computer you will be connecting to. NOTE: Ensure that the Anviz W1 Pro and the computer you will connect to are using the same network.
- Open Paycheckmaster Standard.
- Log in as an administrator with username “admin” and password “admin123”. NOTE: “admin” and “admin123” are the default administrator credentials when the device is first acquired. Contact any higher-ups if the credentials required may have been changed since first use.
- From the tabs at the top of the window, click HRM and Payroll.
- In the section labeled Attendance Management, click Biometric Attendance.
- From the device choices that appear, click Anviz W1 Pro.
- On the window that appears, use the Date pickers to select a starting date and an ending date to set a span of time from which the device will retrieve records.
- Click Load Data From Device.
- Check the table and verify if all the attendance records downloaded are correct.
- Click Save Data Into Database to finalize.
- Click the close button.
ZKTeco WL 20
- Turn on the ZKTeco WL 20.
- Click M/OK to enter the main screen.
- On the main screen, go to System.
- On the System screen, go to Ethernet.
- On the Ethernet screen, go to WIFI setting.
- Select your WIFI network from the list, then press OK.
- Enter the WIFI password.
- Once connected, go back to the WIFI setting screen. NOTE: Ensure that the ZKTeco WL 20 and the computer you will connect to are using the same network.
- On the WIFI setting screen press 0 to go to Advanced.
- Set DHCP to “On”, then go back to the WIFI setting screen.
- Click OK on the WIFI network you are connected to.
- Take note of the IP Address, as you will use it as input later.
- Go back to the Ethernet screen, then go to PC Connection.
- Set Network Mode to “WLAN”.
- Set Port Number to “5010”. Take note of the Port Number, as you will use it as input later.
- Set Password to “0”.
- Set Device ID to “1”.
- You may now go back to the main screen.
- Open Paycheckmaster Standard.
- Log in as an administrator with username “admin” and password “admin123”. NOTE: “admin” and “admin123” are the default administrator credentials when the device is first acquired. Contact any higher-ups if the credentials required may have been changed since first use.
- From the tabs at the top of the window, click Master Module.
- In the section labeled Master Setup Options, click Device Master.
- On the window that appears, input the IP Address from Step 12 in the first textbox and the Port Number from Step 15 in the second textbox.
- Click SAVE, then CLOSE.
- From the tabs at the top of the window, click HRM and Payroll.
- In the section labeled Attendance Management, click Biometric Attendance.
- From the device choices that appear, click ZKTeco WL 20.
- On the window that appears, use the Date pickers to select a starting date and an ending date to set a span of time from which the device will retrieve records.
- Click Load Data From Device.
- Check the table and verify if all the attendance records downloaded are correct.
- Click Save Data Into Database to finalize.
- Click the close button.